![]() How does it work when you have your printer connected to the network both with wireless and wired? You can't have 2 devices with same IP on the network. ![]() If I enter it and connect printer to Wireless network it's the address that my printer will get. I'm using Ubiquity Unifi network solutiuon but it doesn't report any errors related to the printer.Ī side question: in the settings there is an option to provide a static IPv4 address for the printer. I tried to disconnect printer from mains for a long time and connect it without using power surge protection but it didn't help. ![]() I'm running windows 7 on an older lenovo laptop and I've tried rebooting, system restore, reinstalling the drivers, removing lenovo's connectivity program, uninstalling the security update manually but all to no avail. I tried to reset all network settings but it didn't help. The network connection keeps cycling between 'identifying' and 'network cable unplugged' every 2-3 seconds. I have turned off both Wifi connection for the printer as well as Wifi-direct. ![]() I have verified that switch is working correctly and I tried to connect other devices to the same port and they are working fine. I have a network cable that I verified with both a cable tester as well as another PC. When I connect network cable to the printer it's not appering on the network and when I print Configuration Report it states that "Network cable unplugged". I tried to connect my printer to my network using a network cable and I have issues with that. If you want to print my DNS name, chose the Local DNS record option. On the devices tab, select the device, then setting, hit the radio slider for Fixed IP, Choose the network, and enter the IP address. If you are trying to use a fixed IP address, I think it's easier to do that in the UniFi Network Application. If it's set to auto, you can force it to 10Mbps or 100mbps. You can also try to set the speed on your UniFi switch by going into the UniFi Network Application, select the Switch, then select Ports, Port Manager, then the port that the device is connected, Scrool down to Port Profile Overide and use the Link Speed drop down to set the speed. Press the up/down arrows to select one of the following speeds: Press the up/down arrows to select Ethernet Speed and press OK.Ħ. Press the up/down arrows to select Ethernet and press OK.ĥ. Enter the Administrator Password using the alphanumerical keypad. Press the up/down arrows to select Network and press OK.ģ. Setting the Ethernet Speed at the MachineĢ. If you turned of wireless and can't connect to the wired network, try forcing the Ethernet speed to 100Mbps or 10Mbps. Solution 1: Checking Hardware Before we proceed with the troubleshooting, you should make sure that your computer hardware isn’t at fault. You would select either wired or wireless. To fix this issue, you should update the network adapter driver.Hi tonny, the 3225 can only connect to one network at a time. If there is a corrupted network adapter driver or it is out of date, the error “a network cable is not properly plugged in or may be broken” may occur. Step 3: Follow the guide on the screen to finish the process. Step 2: Go to the Troubleshoot tab, locate Network Adapter, and click Run the troubleshooter. Step 1: Click Start > Settings > Update & Security. 1) Swapped cables (I've tried 4) 2) Plugged another laptop into the modem using the same cable now plugged into mine (with success) 3) Updated/Rolled Back the drivers (Realtek PCIe GBE Family Controller btw) - I've tried 3 driver versions now. So, you can try the Network Adapter Troubleshooter to detect and fix the issue. Sometimes the network adapter can be the reason for the error message. Run Windows Network Adapter Troubleshooter Step 3: Re-plug the power button, boot the PC, and see if the issue is fixed. Step 2: Long press the power button for at least 30 seconds and also wait 10 minutes. Step 1: Power off your desktop and unplug all the power cables. Step 4: Check if the Ethernet cable not plugged in or may be broken error disappears. Step 3: Put the battery back, charge the laptop, and turn it on. Step 2: Keep the power button pressed for at least 30 seconds and wait 10 minutes. Step 1: Unplug the charger of your laptop, turn it off, and remove the battery. You can power cycle your computer to refresh the network connection to fix the network cable error. Then, connect the cable to the port and see if you won’t receive “a network cable is not properly plugged in or may be broken”. Just unplug your network cable from the port and then use a piece of dry and clean cloth to wipe the Ethernet port. So, you can clean the port to see if it can fix the issue. If there is dirt or lint in the Ethernet port, it may block the network connection, causing the error message. Solutions to Ethernet Cable May Be Broken or Not Plugged in Clean Your Ethernet Port Tip: Here is a related post for you – If “Network Cable Unplugged” Occurs, Here’s What You Should Do.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |